The GEE Procedure

identifies subjects in the input data set. The subject-effect can be a single variable, an interaction effect, a nested effect, or a combination. Each distinct value (level) of the effect identifies a different subject (cluster). Responses from different subjects are assumed to be statistically independent, and responses within subjects are assumed to be correlated. You must specify a subject-effect, and you must list variables that are used in defining the subject-effect in the CLASS statement.

specifies initial values for log odds ratio regression parameters if you specify the option LOGOR= for data that have either binary or ordinal multinomial responses. The default value of numbers is 0.01.

specifies the convergence criterion for GEE parameter estimation. If the maximum absolute difference between regression parameter estimates is less than number on two successive iterations, convergence is declared. If the absolute value of a regression parameter estimate is greater than 0.08, then the absolute difference normalized by the regression parameter value is used instead of the absolute difference. The default value of number is 0.0001.

displays the estimated regression parameter correlation matrix. Both model-based and empirical correlations are displayed.

displays the estimated working correlation matrix. If you specify TYPE=EXCH for the exchangeable working correlation structure, then the CORRW option is not needed to view the estimated correlation, because a table that contains the single estimated correlation is printed by default.

displays the estimated regression parameter covariance matrix. Both model-based and empirical covariances are displayed.

displays the estimated regression parameter empirical correlation matrix.

displays the estimated regression parameter empirical covariance matrix.

specifies initial values of the regression parameters estimation, other than the intercept parameter, for GEE estimation. If you do not specify this option, then the estimated regression parameters (assuming independence for all responses) are used for the initial values.

specifies an initial value of the intercept regression parameter in the GEE model.

specifies the use of the alternating logistic regression (ALR) method and the regression model structure for the log odds ratio. For data that have either a binary or ordinal multinomial response distribution, the ALR method uses the log odds ratio to model the association of the responses from subjects. For more information about the ALR method and examples of specifying log odds ratio models, see the section Alternating Logistic Regression. You can specify the values that are shown in Table 44.11.

For ordinal multinomial data, only the exchangeable regression structure that is specified by LOGOR=EXCH is supported. You should specify the option LOGOR= or TYPE=, but not both.

specifies the maximum number of iterations allowed in the iterative GEE estimation process. By default, MAXITER=50.

displays the estimated regression parameter model-based correlation matrix.

displays the estimated regression parameter model-based covariance matrix.

displays a parameter estimates table that uses model-based standard errors for inference. By default, a "Parameter Estimates" table that is based on empirical standard errors is displayed.

specifies a variable that defines subclusters for the 1-nested or k-nested log odds ratio association modeling structures for data that have a binary response distribution. A 1-nested or k-nested modeling structure is specified in the option LOGOR=, and variable must be listed in the CLASS statement. For definitions of the 1-nested and k-nested modeling structures, see the section Specifying Log Odds Ratio Models.

specifies the structure of the working correlation matrix that is used to model the correlation of the responses from subjects for ordinary GEEs. You can specify the values that are shown in Table 44.12 (for definitions of the correlation matrix types, see Table 44.13 in the section Details: GEE Procedure).

For example, the following option specifies a fixed correlation matrix:

type=user( 1.0  0.9  0.8  0.6
           0.9  1.0  0.9  0.8
           0.8  0.9  1.0  0.9
           0.6  0.8  0.9  1.0 )

By default, TYPE=IND. When you specify the alternating logistic regression method using the option LOGOR= you should not specify TYPE=.

defines an effect that specifies the order of measurements within subjects. Each distinct level of the within-subject-effect defines a different response from the same subject. If the data are in proper order within each subject, you do not need to specify this option.

If some measurements do not appear in the data for some subjects, this option properly orders the existing measurements and treats the omitted measurements as missing values.

If you do not specify the WITHIN= option for the standard GEE method, missing values are assumed to be the last values and are not used; the remaining observations are then ordered in the sequence in which they are provided in the input data set. If you do not specify the WITHIN= option for the weighted GEE method, the observations are assumed to be ordered in the sequence in which they are provided in the input data set.

Variables that are used in defining the within-subject-effect must be listed in the CLASS statement.

specifies a SAS data set that contains either the full matrix for log odds ratio association modeling for data with binary responses or the matrix for a single complete cluster to be replicated for all clusters.

specifies the variables in the ZDATA= data set that correspond to rows of the matrix for log odds ratio association modeling for data with binary responses.